SMT-CEW/D-3000 Mobile/Immobile Magnetic Particle Flaw Detection Machine

·This machine is equipped with advanced 303D magnetization power source and E-40 black light. Magnetization AC current or half wave DC current may be selected to carry our round, vertical magnetization and fluorescent magnetic particle flaw detection with high intensity of UV light. Digital display of magnetization current with upper and lower limit preset. It also has demagnetization function.
Magnetization power source with bottom roller may be pulled out, which can carry out flaw detection on the large scale work-pieces with 触头 method and 烧电缆 method. This machine is suitable to these manufactures which have small quantity of work-piece with wide variety of type and size.
·Power supply: AC 220V.50Hz, 80A,single phase.
·Magnetization current output: AC 0-3000A(peak to peak)
·Demagnetization: AC 0-3000A(peak to peak)
·Rate of load: 10%
·Maximum distance between clamp: 0-800mm
·Coil of magnetization: 8 turns, diameter: 300mm, movable.
·Liquid tank volume: 25 liter
·Intensity of UV light: at 380mm under the filter:³14000muw/cm².

SMT-CEW-4000 Series AC/DC Magnetic Particle Flaw Detection Machine

·Vertical Magnetization is performed by closed loop yoke and auxiliary coil. It is suitable to work-piece in comp1ex shape such as shaft etc. Its semiautomatic operation function is under PLC control. Operator may adjust parameters on control panel, high intensity UV light mounting is available if required.
·Power supply: AC 380V, 50Hz, 3 phases, and 4 lines
·Maximum instantaneous input power: 32KVA
·Round magnetic current (AC): 0-4000A (RMS) non-graded adjustment.
·Vertical magnetic DC current: yoke only, 0-28000 AT (current:0-l2.5A)
·To use Yoke and coil simutaneously: 0-30000 AT (current:0-10A)
·Demagnetization on the machine: Round AC damping Voltage demagnetization voltage decreasing: non-graded. Vertical DC demagnetization: voltage decreasing with change in polarity, rate of decreasing voltage: non-graded, frequency of change in polarity is adjustable.
·Distance between clamps: 0-l250mm, adjustable.
·Central height of magnetizing: 285mm
·Diameter of magnetization c1amp: 170mm
·Inner diameter of movable coil: 300mm
·Rate of load: 20%
· Liquid tank volume:³25L

SMT-CZW-4000G DC Fluorescent Magnetic Particle Flaw Detection Machine (Special for Steel Pipe )

·The machine is built and designed for crude oil steel pipe Internal and external magnetization of work-piece with various specification, new designing logo of spray and inspection, PLC programming control, demagnetization function, 2 high intensity UV light equipped, explicit indication of inside and outside surface defect.
·Power supply/instantaneous maximum input power: 50Hz, 380v, 3-phase, 4-line/32KVA
·Round magnetization(full wave DC); 0-4000A穿棒式通电.
·Vertical magnetization(full wave DC): Closed loop yoke, 0-28800AT magnetization current: 0-12.5A
·Automatic demagnetization: 0-500mm.adjustable
·Central height of magnetization clamp: 285mm
·Diameter of magnetization clamp: 210mm
·Intensity of UV light:
at 380mm under the filter: 3400uwi/cm2(E-50)
at 380mm under the filter: 3800uwi/cm2(D-20B)
·System of magnetic suspend liquid: New stirring method, liquid tank may be pulled out along slide.
·Application of flaw detection work: 油管接箍，套管接箍 maximum outer diameter 195mm, minimum one: 73mm

 

SMT-CJW-1000TZ AC Fluorescent Magnetic Particle Flaw Detection Machine (Special for Spring)

·This machine is built and designed for automobile car spring production line, it is fully automatic control system by PLC grogram, springs are conveyed into position, automatic rotation of spring and demagnetization are performable. Spring is classified by inspector by inspector and then removed automatically. The rate of test is 8 seconds per spring work-piece. Client is satisfied with its sensitivity of test.
·Power supply: AC 50Hz, 380V, 3-phase and 4-line
·Maximum instantaneous input power: 10KVA
·Magnetization current(AC): 0-1000A(RMS), non-graded adjustment.
·Distance between clamps: 0-500mm, adjustable
·Volume of liquid tank: 35L
·Magnetic force pump for sucking and stirring: 380V, 0.55KW,扬程 10m.
·Scope of application of spring: stress spring in cylindrical shape, outer diameter: F5-200mm, length: 230-500mm.
·Rate of test 8 seconds per work-piece

 

 

MP-A2L Handy Magna

·Power: AC 220V/50Hz/60Hz
·Current: 2.5A(without load), 2.0A
·Distance between magnetic polarity: 84-l76mm
·Weight: 3.2Kg
·Lifting force : 12Lb(5.45Kg) or over
·Illumination bulb: 12V, 5W
·Power cable length: 4.5m

MP-A2D Handy Magna

·Polarity: l30mm
·Power: DC12V
·Current: 2.8A
·Size: Length* Height* Width
              194*   182  *24 (main machine)
              125*    117 * 76 (battery)
·Lifting force: 18.2Kg or over
·Power cable length: 2m
·Circulation of operation and time of use: 10 seconds on, 10 seconds off , 4 hours or over
· Weight: 2Kg main machine, l.3Kg battery, 1.6Kg battery charger.